AR-15 Gunsmithing & 9mm AR Upper Conversions

The following are costs for AR-15 rifle work. Not all possible jobs are listed, but you may call and ask for Rick Corbin,  a combat rifle specialist, who has worked in the Ten-Ring shop for over fifteen years. Rick has considerable experience overhauling, accurizing, fine tuning and bringing your rifle up to match grade standards and combat level with flawless function at a reasonble price.

 1a. Install Picatiny rail for scopes and combat flashlights……………….Price depends on the brand of rail and how it is attached.

  1. Cut and crown……………………………………………………………$95.00
  2. Cut & thread for supressor or muzzle break (1/2 X 28TPI)…..$145.00
  3. Gun Kote with any color polymer finish 100%………………………$325.00
  4. Gun Kote upper unit only…………………………………………….$175.00
  5. Gun Kote lower unit only………………………………………………$175.00
  6. Fantastic trigger job using parts already in your rifle with internal overtravel stop and undertravel (short reset)…………………………$165.00
  7. Mount scope (cost depends on several factors.)…………………..$45.00+
  8. Replace gas block (price includes most gas blocks.)…………….$85.00
  9. Install DPMS bull barrel (includes barrel)…………………………$300.00
  10.   Complete strip-down cleaning and carbon removal$45.00

We have a shop minimum of $45.00 with an hourly rate of $45.00 to $65.00 per hour depending on the complesity of the work.

________________________________________

AR 9mm Upper Conversions With Steel Magazine Block

We build and sell high quality 9mm “drop-in” conversions, with a flattop Picatinny rail in the rear and with or without an “A” frame front sight for your AR style rifle which will allow you to shoot cheap 9mm ammunition.  All you do is remove your current upper and install the new Ten-Ring Precision 9mm upper which comes complete with an “all steel” magazine block and one 25, 30 or 40 round 9mm magazineExtra magazines are $45.00.  California ten round mags may be available from Metalform in the future, but the ones sold now do not function. 
You do not need to make any alterations to your lower unit or change buffers, just attach to the standard mounting pins and start shooting.  Some of the older 1982 vintage Colt receiver mounting holes may be too large to accept the modern pins and will have to be bushed with bushings available from Brownell’s and others.
The actual barrel length is 11 3/4″ with a 5 1/2″ welded-on flash hider extension for a total of 16 1/4″ legal length. The bolt camming edge is beveled where it contacts the hammer. 
You can purchase one of these fine, very accurate, inexpensive to shoot, 9mm uppers without having to go through a Federal licensed dealer for $625.00 plus $25.00 UPS shipping which includes handling, insurance, signature and residential delivery.
The A-4 and A-2 pictured.

    

AR-15 9mm ”Pistol” Uppers

(All NFA regulations apply)

  These unique, interesting and hard to find uppers are just like the full size uppers described above except the barrel length is 8″ and 9 1/4″ with the flash hider. They fit to your lower unit exactly like any other upper. All you do is remove the current upper and install the new 9mm pistol which comes complete with one 25, 30 or 40 round magazine and one “all steel” magazine block.  Ten round mags will be available from Metalform in about the first of 2014.

These unique little units sell for $625.00 which includes one 25, 32 or 40 round magazine and one ”all steel” mag block.   Add UPS second day shipping which usually runs around $45.00 or UPS Ground which will be around $25.00).  All shipping includes insurance, residential delivery and signature.